herunterladen
Features
• High Performance, Low Power AVR
®
8-Bit Microcontroller
• Advanced RISC Architecture
– 130 Powerful Instructions – Most Single Clock Cycle Execution
– 32 x 8 General Purpose Working Registers
– Fully Static Operation
– Up to 16 MIPS Throughput at 16 MHz (ATmega165PA/645P)
– Up to 20 MIPS Throughput at 20 MHz
(ATmega165A/325A/325PA/645A/3250A/3250PA/6450A/6450P)
– On-Chip 2-cycle Multiplier
• High Endurance Non-volatile Memory segments
– In-System Self-programmable Flash Program Memory
• 16K Bytes (ATmega165A/ATmega165PA)
• 32K Bytes (ATmega325A/ATmega325PA/ATmega3250A/ATmega3250PA)
• 64K Bytes (ATmega645A/ATmega645P/ATmega6450A/ATmega6450P)
–EEPROM
• 512 Bytes (ATmega165A/ATmega165PA)
• 1K bytes (ATmega325A/ATmega325PA/ATmega3250A/ATmega3250PA)
• 2K bytes (ATmega645A/ATmega645P/ATmega6450A/ATmega6450P)
–Internal SRAM
• 1K Bytes (ATmega165A/ATmega165PA)
• 2K Bytes (ATmega325A/ATmega325PA/ATmega3250A/ATmega3250PA)
• 4K Bytes (ATmega645A/ATmega645P/ATmega6450A/ATmega6450P)
– Write/Erase cycles: 10,000 Flash/100,000 EEPROM
– Data retention: 20 years at 85°C/100 years at 25°C
(1)
– Optional Boot Code Section with Independent Lock Bits
• In-System Programming by On-chip Boot Program
• True Read-While-Write Operation
– Programming Lock for Software Security
• QTouch
®
library support
– Capacitive touch buttons, sliders and wheels
– QTouch and QMatrix acquisition
– Up to 64 sense channels
• JTAG (IEEE std. 1149.1 compliant) Interface
– Boundary-scan Capabilities According to the JTAG Standard
– Extensive On-chip Debug Support
– Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface
• Peripheral Features
– Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode
– One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode
– Real Time Counter with Separate Oscillator
– Four PWM Channels
– 8-channel, 10-bit ADC
– Programmable Serial USART
– Master/Slave SPI Serial Interface
– Universal Serial Interface with Start Condition Detector
– Programmable Watchdog Timer with Separate On-chip Oscillator
– On-chip Analog Comparator
– Interrupt and Wake-up on Pin Change
• Special Microcontroller Features
– Power-on Reset and Programmable Brown-out Detection
– Internal Calibrated Oscillator
– External and Internal Interrupt Sources
– Five Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, and Standby
• I/O and Packages
– 54/69 Programmable I/O Lines
– 64/100-lead TQFP, 64-pad QFN/MLF and 64-pad DRQFN
• Speed Grade:
– ATmega 165A/165PA/645A/645P: 0 - 16 MHz @ 1.8 - 5.5V
– ATmega325A/325PA/3250A/3250PA/6450A/6450P: 0 - 20MHz @ 1.8 - 5.5V
• Temperature range:
–-40°C to 85°C Industrial
• Ultra-Low Power Consumption (picoPower devices)
– Active Mode:
• 1 MHz, 1.8V: 215 µA
• 32 kHz, 1.8V: 8 µA (including Oscillator)
– Power-down Mode: 0.1 µA at 1.8V
– Power-save Mode: 0.6 µA at 1.8V (Including 32 kHz RTC
Note: 1. Reliability Qualification results show that the projected data retention failure rate is much less than 1 PPM
over 20 years at 85°C or 100 years at 25°C.
8-bit
Microcontroller
with 16/32/64K
Bytes In-System
Programmable
Flash
ATmega165A
ATmega165PA
ATmega325A
ATmega325PA
ATmega3250A
ATmega3250PA
ATmega645A
ATmega645P
ATmega6450A
ATmega6450P
Preliminary
Rev 8285A–AVR–10/10
Verzeichnis
- ・ Konfiguration des Pinbelegungsdiagramms on Seite 2 Seite 6 Seite 70 Seite 94 Seite 140
- ・ Abmessungen des Paketumrisses on Seite 666 Seite 667 Seite 668 Seite 669
- ・ Teilenummerierungssystem on Seite 656 Seite 657 Seite 658 Seite 659 Seite 660
- ・ Blockdiagramm on Seite 4 Seite 10 Seite 68 Seite 94 Seite 95
- ・ Typisches Anwendungsschaltbild on Seite 204
- ・ Beschreibung der Funktionen on Seite 199
- ・ Technische Daten on Seite 68
- ・ Anwendungsbereich on Seite 38 Seite 46 Seite 56 Seite 60 Seite 266
- ・ Elektrische Spezifikation on Seite 68
