herunterladen
CapTouch Programmable Controller for
Single-Electrode Capacitance Sensors
Data Sheet
AD7147
Rev. D
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.461.3113 ©2007–2011 Analog Devices, Inc. All rights reserved.
FEATURES
Programmable capacitance-to-digital converter (CDC)
Femtofarad resolution
13 capacitance sensor inputs
9 ms update rate, all 13 sensor inputs
No external RC components required
Automatic conversion sequencer
On-chip automatic calibration logic
Automatic compensation for environmental changes
Automatic adaptive threshold and sensitivity levels
Register map is compatible with the AD7142
On-chip RAM to store calibration data
SPI-compatible (serial-peripheral-interface-compatible)
serial interface (AD7147)
I
2
C-compatible serial interface (AD7147-1)
Separate V
DRIVE
level for serial interface
Interrupt output and general-purpose input/output (GPIO)
24-lead, 4 mm × 4 mm LFCSP
2.6 V to 3.3 V supply voltage
Low operating current
Full power mode: 1 mA
Low power mode: 21.5 µA
Qualified for automotive applications
APPLICATIONS
Cell phones
Personal music and multimedia players
Smart handheld devices
Television, A/V, and remote controls
Gaming consoles
Digital still cameras
GENERAL DESCRIPTION
The AD7147 CapTouch™ controller is designed for use with
capacitance sensors implementing functions such as buttons,
scroll bars, and wheels. The sensors need only one PCB layer,
enabling ultrathin applications.
The AD7147 is an integrated CDC with on-chip environmental
calibration. The CDC has 13 inputs channeled through a switch
matrix to a 16-bit, 250 kHz sigma-delta (∑-∆) converter. The CDC
is capable of sensing changes in the capacitance of the external
sensors and uses this information to register a sensor activation.
By programming the registers, the user has full control over the
CDC setup.
High resolution sensors require minor software to run on the
host processor.
FUNCTIONAL BLOCK DIAGRAM
CALIBRATION
ENGINE
SERIAL INTERFACE
AND CONTROL LOGIC
CALIBRATION
RAM
POWER-ON
RESET LOGIC
INTERRUPT
AND GPIO
LOGIC
EXCITATION
SOURCE
A
C
SHIELD
V
CC
GND BIAS
CONTROL
AND DATA
REGISTERS
16-BIT
-
CDC
SWITCH
MATRIX
19
CIN0
20
CIN1
21
CIN2
22
CIN3
23
CIN4
24
CIN5
1
CIN6
2
CIN7
3
CIN8
4
CIN9
5
CIN10
6
CIN11
7
CIN12
V
DRIVE
GPIO
8 11 10 9
1812
13 14 15 16 17
SDO/
SDA
SDI/
ADD0
SCLK CS/
ADD1
INT
AD7147/
AD7147-1
06663-001
Figure 1.
The AD7147 is designed for single electrode capacitance
sensors (grounded sensors). There is an active shield output to
minimize noise pickup in the sensor.
The AD7147 has on-chip calibration logic to compensate for
changes in the ambient environment. The calibration sequence
is performed automatically and at continuous intervals as long
as the sensors are not touched. This ensures that there are no
false or nonregistering touches on the external sensors due to
a changing environment.
The AD7147 has an SPI-compatible serial interface, and the
AD7147-1 has an I
2
C®-compatible serial interface. Both parts have
an interrupt output, as well as a GPIO. There is a V
DRIVE
pin to set
the voltage level for the serial interface independent of V
CC
.
The AD7147 is available in a 24-lead, 4 mm × 4 mm LFCSP and
operates from a 2.6 V to 3.6 V supply. The operating current con-
sumption in low power mode is typically 26 A for 13 sensors.
Verzeichnis
- ・ Konfiguration des Pinbelegungsdiagramms on Seite 10 Seite 71
- ・ Abmessungen des Paketumrisses on Seite 40 Seite 71
- ・ Paket-Footprint-Pad-Layout on Seite 40
- ・ Teilenummerierungssystem on Seite 71
- ・ Blockdiagramm on Seite 1
- ・ Typisches Anwendungsschaltbild on Seite 42
- ・ Beschreibung der Funktionen on Seite 1 Seite 10 Seite 71
- ・ Technische Daten on Seite 1 Seite 5 Seite 6 Seite 7 Seite 8
- ・ Anwendungsbereich on Seite 1 Seite 71
- ・ Elektrische Spezifikation on Seite 11
