herunterladen
Semiconductor Components Industries, LLC, 2004
July, 2004 − Rev. 13
1 Publication Order Number:
MC7800/D
MC7800, MC7800A,
NCV7805
1.0 A Positive Voltage
Regulators
These voltage regulators are monolithic integrated circuits designed
as fixed−voltage regulators for a wide variety of applications
including local, on−card regulation. These regulators employ internal
current limiting, thermal shutdown, and safe−area compensation. With
adequate heatsinking they can deliver output currents in excess of
1.0 A. Although designed primarily as a fixed voltage regulator, these
devices can be used with external components to obtain adjustable
voltages and currents.
• Output Current in Excess of 1.0 A
• No External Components Required
• Internal Thermal Overload Protection
• Internal Short Circuit Current Limiting
• Output Transistor Safe−Area Compensation
• Output Voltage Offered in 2% and 4% Tolerance
• Available in Surface Mount D
2
PAK−3, DPAK−3 and Standard
3−Lead Transistor Packages
• NCV Prefix for Automotive and Other Applications Requiring Site
and Control Changes
• Pb−Free Packages are Available
MAXIMUM RATINGS (T
A
= 25°C, unless otherwise noted)
Value
Unit
Rating Symbol
369C 221A
936
Input Voltage (5.0 − 18 V)
(24 V)
V
I
35
40
Vdc
Power Dissipation P
D
Internally Limited W
Thermal Resistance,
Junction−to−Ambient
R
JA
92 65 Figure 14 °C/W
Thermal Resistance,
Junction−to−Case
R
JC
5.0 5.0 5.0 °C/W
Storage Junction
Temperature Range
T
stg
−65 to +150 °C
Operating Junction
Temperature
T
J
+150 °C
Maximum ratings are those values beyond which device damage can occur.
Maximum ratings applied to the device are individual stress limit values (not
normal operating conditions) and are not valid simultaneously. If these limits are
exceeded, device functional operation is not implied, damage may occur and
reliability may be affected.
NOTE: ESD data available upon request.
TO−220−3
T SUFFIX
CASE 221A
1
D
2
PAK−3
D2T SUFFIX
CASE 936
2
3
See detailed ordering and shipping information in the package
dimensions section on page 21 of this data sheet.
ORDERING INFORMATION
Heatsink surface
connected to Pin 2.
Pin 1. Input
2. Ground
3. Output
Heatsink surface (shown as terminal 4 in
case outline drawing) is connected to Pin 2.
1
3
STANDARD APPLICATION
A common ground is required between the
input and the output voltages. The input voltage
must remain typically 2.0 V above the output
voltage even during the low point on the input
ripple voltage.
XX,
MC78XX
Input
C
in
*
0.33 F
C
O
**
Output
These two digits of the type number
indicate nominal voltage.
C
in
is required if regulator is located an
appreciable distance from power supply
filter.
C
O
is not needed for stability; however,
it does improve transient response. Values
of less than 0.1 F could cause instability.
*
**
See general marking information in the device marking
section on page 25 of this data sheet.
DEVICE MARKING INFORMATION
DPAK−3
DT SUFFIX
CASE 369C
http://onsemi.com
1
2
3
4
Verzeichnis
- ・ Abmessungen des Paketumrisses on Seite 26 Seite 27 Seite 28
- ・ Paket-Footprint-Pad-Layout on Seite 27 Seite 28
- ・ Teilenummerierungssystem on Seite 1 Seite 21 Seite 22 Seite 23 Seite 24
- ・ Markierungsinformationen on Seite 1 Seite 25
- ・ Blockdiagramm on Seite 2
- ・ Technische Daten on Seite 21 Seite 22 Seite 23 Seite 24 Seite 25
- ・ Anwendungsbereich on Seite 1 Seite 19
- ・ Elektrische Spezifikation on Seite 3 Seite 4 Seite 5 Seite 6 Seite 7
